2/2) Refine structure with SHELXL.

The SHELXL refinement runs in the usual way, and prints the following to the screen:

Notice that the wR2 value starts very high (~75%), but rapidly plummets down to ~33% at the end. From the looks of it, it is probably not completely converged, but at this stage that is not so important. It is also worth noting that the difference map features ie. the "Highest peak" and "Deepest hole" indicate that there are no dramatically wrong or missing atoms. To get a proper handle on whether the refinement run was a success, a graphical view is a must. Here's what XP shows:

At first glance that looks pretty bad, but on closer inspection it is probably fixable. In the last SHELXL run, the restraints pulled the molecules apart at the bottom, and created a pair of very distorted sulphur-containing rings. It is well to remember that these programs do not know any chemistry. They simply do what they are told to do, and in this case, manual intervention is necessary. The weird S-containing rings can be fixed by swapping the coordinates of C8 and C8'. In a similar way, switching C1 with C5' and C1' with C5 should restore the connectivity of each PART, and highlight the improved geometry over the starting model.

The editing is easily done by hand using cut/paste in a text editor, giving something like this:

In the above image, the coordinates of the aforementioned atoms have been switched and a REM comment added to explain what was done. The REM is not strictly necessary, but it always helps to keep good notes, and the '.ins' file is a better place than on scraps of easily lost paper. In any event, when filed as a new '.ins' file and run through SHELXL again, the following is output to the screen.

The resulting geometry now looks pretty good (look at it with XP if you like). It's time to think about adding hydrogen atoms and going anisotropic etc.

Before adding hydrogens, however, we need to know where the double bond is (or if it is scrambled by additional disorder, as per the initial suspicion). In the XP window above, the BANG command shows that C5=C6 (and C5'=C6') are double bonds, while C4-C5 (and C4'-C5') are single. Often it is best to err on the side of caution, so we'll run a refinement without adding the methylene-type hydrogens to C4 and C4'. Thus, for the next refinement run the following HFIX commands go in the '.ins' file:

HFIX 43 C5 C6 C5' C6'
HFIX 137 C1 C9 C1' C9'

It is possible with the disorder, that HFIX 137 will lead to non-convergence, but if that is the case the '137' will be changed to '33' later. This refinement gives the following ...

... which looks like this after removal of all but the four largest difference map peaks:

Those green Q-peaks look a lot like methylene hydrogen atom positions ...

... in spite of their small size (0.24-0.35 eÅ-3). Subsequent refinement with anisotropic displacement parameters (ANIS in the '.ins') gives the following:

That's not all good news. SHELXL gives a warning about two atoms being 'NPD', or non-positive definite, which in plain language means that the 'ellipsoids' for those two atoms are not closed (i.e. they are not actually ellipsoids). To proceed, we need to know which atoms are causing trouble. This is given in the '.lst' file, which includes all sorts of useful diagnostics from the SHELXL run. Here's the relevant part of the '.lst' file:

A quick look at the superimposed PARTs shows C3 and C3' virtually on top of each other, so it is not in the least surprising that SHELXL couldn't refine separate ADPs for these atoms. C9 and C9' are in similar danger. Atoms that overlap like this need to have their ADPs fixed with EADP, or perhaps with very strong restraints. This is also a good opportunity to relax and change the restraints on geometry and other ADPs as well.

For the last rounds of refinement, the following changes were made:

SAME 0.02 S1' > C9'
RIGU 0.01 S1 > C9'
ISOR 0.005 C3 C3'

Here, RIGU is a new 'enhanced rigid bond' restraint in the latest release of SHELXL. This refinement gave the following screen output.

In the above, it is clear that the refinement has converged because the "Max. shift/esd" is zero. The difference map is also quite flat, and other refinement statistics are acceptable. The only things left are small tasks such as checking the weighting scheme (WGHT), testing for possible extinction (EXTI), and ensuring that the centroid of the molecule(s) are within the unit cell box. The latter is just for the sake of aesthetics.

The final model, as drawn with shelXle is shown above. It could be argued that the ADPs of the related atoms in the two disordered parts should be constrained about the 2-fold rotation axis that relates them. That would be nice, but such minutiae would make little difference to the model.

1) Solve structure using SHELXS and XP.
2) Refine structure with SHELXL.